This includes a new summary mode (-s) for camcontrol defects that
quickly tells the user the most important thing: how many defects
are in the requested list. The actual location of the defects is
less important.
Modern drives frequently have more than the 8191 defects that can
be reported by the READ DEFECT DATA (10) command. If they don't
have that many grown defects, they certainly have more than 8191
defects in the primary (i.e. factory) defect list.
The READ DEFECT DATA (12) command allows for longer parameter
lists, as well as indexing into the list of defects, and so allows
reporting many more defects.
This has been tested with HGST drives and Seagate drives, but
does not fully work with Seagate drives. Once I have a Seagate
spec I may be able to determine whether it is possible to make it
work with Seagate drives.
scsi_da.h: Add a definition for the new long block defect
format.
Add bit and mask definitions for the new extended
physical sector and bytes from index defect
formats.
Add a prototype for the new scsi_read_defects() CDB
building function.
scsi_da.c: Add a new scsi_read_defects() CDB building function.
camcontrol(8) was previously composing CDBs manually.
This is long overdue.
camcontrol.c: Revamp the camcontrol defects subcommand. We now
go through multiple stages in trying to get defect
data off the drive while avoiding various drive
firmware quirks.
We start off by requesting the defect header with
the 10 byte command. If we're in summary mode (-s)
and the drive reports fewer defects than can be
represented in the 10 byte header, we're done.
Otherwise, we know that we need to issue the
12 byte command if the drive reports the maximum
number of defects.
If we're in summary mode, we're done if we get a
good response back when asking for the 12 byte header.
If the user has asked for the full list, then we
use the address descriptor index field in the 12
byte CDB to step through the list in 64K chunks.
64K is small enough to work with most any ancient
or modern SCSI controller.
Add support for printing the new long block defect
format, as well as the extended physical sector and
bytes from index formats. I don't have any drives
that support the new formats.
Add a hexadecimal output format that can be turned
on with -X.
Add a quiet mode (-q) that can be turned on with
the summary mode (-s) to just print out a number.
Revamp the error detection and recovery code for
the defects command to work with HGST drives.
Call the new scsi_read_defects() CDB building
function instead of rolling the CDB ourselves.
Pay attention to the residual from the defect list
request when printing it out, so we don't run off
the end of the list.
Use the new scsi_nv library routines to convert
from strings to numbers and back.
camcontrol.8: Document the new defect formats (longblock, extbfi,
extphys) and command line options (-q, -s, -S and
-X) for the defects subcommand.
Explain a little more about what drives generally
do and don't support.
Sponsored by: Spectra Logic
MFC after: 1 week
showing up on Haswell-class CPUs
From the Intel SDM, "Table 3-20. Feature Information Returned in the
ECX Register"
11 | SDBG | A value of 1 indicates the processor supports
IA32_DEBUG_INTERFACE MSR for silicon debug.
Submitted by: jiashiun@gmail.com
Reviewed by: jhb neel
MFC after: 2 weeks
data to go undetected.
The probe code does an MD5 checksum of the inquiry data (and page
0x80 serial number if available) before doing a reprobe of an
existing device, and then compares a checksum after the probe to
see whether the device has changed.
This check was broken in January, 2000 by change 56146 when the extended
inquiry probe code was added.
In the extended inquiry probe case, it was calculating the checksum
a second time. The second time it included the updated inquiry
data from the short inquiry probe (first 36 bytes). So it wouldn't
catch cases where the vendor, product, revision, etc. changed.
This change will have the effect that when a device's inquiry data is
updated and a rescan is issued, it will disappear and then reappear.
This is the appropriate action, because if the inquiry data or serial
number changes, it is either a different device or the device
configuration may have changed significantly. (e.g. with updated
firmware.)
scsi_xpt.c: Don't calculate the initial MD5 checksum on
standard inquiry data and the page 0x80 serial
number if we have already calculated it.
MFC after: 1 week
Sponsored by: Spectra Logic
kernel via the global cpuset_domain[] array. To export these to userland,
add a CPU_WHICH_DOMAIN level that can be used to fetch the mask for a
specific domain. Add a -d flag to cpuset(1) that can be used to fetch
the mask for a given domain.
Differential Revision: https://reviews.freebsd.org/D1232
Submitted by: jeff (kernel bits)
Reviewed by: adrian, jeff
packages intended to be included on the DVD, and
remove any nonexistent ports from the final list.
Print the list of missing paths, and ensure that
DVD_PACKAGES is non-zero length (which should never
happen).
MFC after: 3 days
X-MFC-With: r276820, r276822
Sponsored by: The FreeBSD Foundation
- Fix depend target by removing a space after an "-I" inclusion option.
- Fix some minor compile issues in the "osmtest" utility.
MFC after: 3 days
PR: 196580
Sponsored by: Mellanox Technologies
with calls to the centralised macros, reducing direct use of MLEN and
MHLEN.
Differential Revision: https://reviews.freebsd.org/D1444
Reviewed by: bz
Sponsored by: EMC / Isilon Storage Division
that some #ifdef SMP code is also conditional on __ARM_ARCH >= 7; we don't
support SMP on armv6, but some drivers and modules are compiled with it
forced on via the compiler command line.
These tools are now from the ELF Tool Chain project:
* addr2line
* elfcopy (strip)
* nm
* size
* strings
The binutils versions are available by setting in src.conf:
WITHOUT_ELFTOOLCHAIN_TOOLS=yes
Thanks to antoine@ for multiple exp-runs and diagnosing many of the
failures.
PR: 195561 (ports exp-run)
Sponsored by: The FreeBSD Foundation
[Aarch64] Customer lowering of CTPOP to SIMD should check for NEON
availability
This ensures llvm's AArch64 backend does not emit floating point
instructions if they are disabled.
For this to work the driver needs to know the bank it has attached to since
the registers for the first 12 pins are at a different location.
Move the lock initialization to simplify the code.
to ease any rework of how clang is built to take arm64 in to account.
Submitted by: andrew
Reviewed by: andrew, emaste
Differential Revision: https://reviews.freebsd.org/D1446
in the NFS server; garbage collect now-unused NFSMSIZ() and M_HASCL()
macros. Also garbage collect now-unused versions in headers for the
removed previous NFS client and server.
Reviewed by: rmacklem
Sponsored by: EMC / Isilon Storage Division
isn't supposed to manage all the GPIO pins in the system from a single
instance, instead it will attach to each one of the four available GPIO
controllers and only deal with one bank at time (32 pins per bank).
Rework part of the driver to take advantage of that, this simplify the
code a lot.
Also fix a bug in rk30_gpio_get_function() which wouldn't return the
correct values.
While here fix a typo in register name.
This avoids universe trying to build MALTA_COMMON and fail due to
the problem addressed in r276773.
Include std.MALTA from the MALTA mipsel and MALTA64 mips64el config files,
where the machine lines exist.
code in sys/kern/kern_dump.c. Most dumpsys() implementations are nearly
identical and simply redefine a number of constants and helper subroutines;
a generic implementation will make it easier to implement features around
kernel core dumps. This change does not alter any minidump code and should
have no functional impact.
PR: 193873
Differential Revision: https://reviews.freebsd.org/D904
Submitted by: Conrad Meyer <conrad.meyer@isilon.com>
Reviewed by: jhibbits (earlier version)
Sponsored by: EMC / Isilon Storage Division
When not using the --foreground option timeout(1) is supported to signal all
command children hierarchy, timeout(1) now acquire the reaper to ensure this
really happens and no children process can escaper from timeout(1) control
Kenneth D. Merry